精品少妇人妻av免费久久农村,一级片久久,91天堂视频,国产破处

Welcome [Wuxi Yi Jin Machinery Co. Ltd.] official website!
Chinese   |   English   |  Sitemap
Explosion proof

Position:Home > Explosion proof >

  • B4-72C

    B4-72C

    MORE+

  • B4-72C

    B4-72C

    MORE+

  • B4-72C

    B4-72C

    MORE+

  • FB9-12C

    FB9-12C

    MORE+

  • FB9-12C

    FB9-12C

    MORE+

  • FB9-12C

    FB9-12C

    MORE+

 Centrifugal fan in the end is how to install, centrifugal fan manufacturers of workers is described as follows:
1. Centrifugal fan of the overall unit installation, should be placed directly on the basis of pairs of oblique horn leveling.
2. On-site assembly of the centrifugal fan, the base of the cutting surface should be properly protected, there should be no corrosion or operation, the base placed on the basis of the application of pairs of oblique horn leveling.
3. The bearing seat and the base should be tightly engaged, the vertical non-level should not exceed 0.2 / 1000, with the level on the spindle measurement, horizontal horizontal water should not exceed 0.3 / 1000, with the level of the bearing in the level of the sub-surface measuring.
4. Before the bearing grinding, the rotor axis should be corrected with the axis of the chassis, and the gap between the impeller and the inlet and the clearance between the spindle and the rear side of the housing should be adjusted to match the equipment technology The provisions of the document.
5. When the spindle and the bearing are assembled, they should be inspected according to the equipment technical documents. Bearing bearing and bearing pad should be maintained between 0.03-0.04 mm interference.
6. When the fan housing is assembled, the position of the housing should be determined on the basis of the rotor axis and the axial and radial clearance between the inlet of the impeller and the air inlet of the cabinet should be high and within the specified range. Whether the anchor bolts are fastened. If the gap is not specified in the technical documentation, the general axial clearance shall be 1/100 of the outer diameter of the impeller. The radial clearance shall be evenly distributed. The value shall be 1.5 / 1000-3 / 1000 of the outer diameter of the impeller. Adjust the value of the gap to try to improve the efficiency of the fan.
7. When the fan is correct, the fan shaft and the motor shaft of different degrees of axis: radial displacement should not exceed 0.05 mm, the tilt should not exceed 0.2 / 1000.
8. Rolling bearing assembly of the centrifugal fan, the two bearing frame on the bearing hole of different shaft degrees, until the rotor is installed, to flexible rotation prevail.

Contact: Mr. Wei 180 6833 7327 / 133 9518 5578 7 ????Tel: 0510-83303276 ????Fax: 0510-83303276

E-mail: 2637472470@qq.com ????Web: ????Add: Luoxian Town, Huishan District, Wuxi City

Copy right ? 2017 Wuxi Yi Jin Machinery Co., Ltd. All Rights Reserved

国产熟睡乱子伦午夜视频| 老牛精品亚洲成av人片| 成人午夜国产内射主播| 精品AⅤ一区二区三区| 国产美女久久精品香蕉| 佛教| av超碰| 亚洲激情一区| 波多野在线| 久久久久97| 人妻少妇精品中文字幕av蜜桃| 制服丝袜久久| 欧美a级片| 嫩草在线| 亚洲精品1| 男女27报xxoo做爰高潮| 亚洲色图五月天| jzjzjz亚洲丰满少妇| h电影在线观看| 成人色在线| 色一欲一性一乱—区二区三区| 国产美女一级特黄大片| 亚洲成a人片77777kkkk| 色琪琪丁香婷婷综合久久| 国产真乱mangent| 欧美性爽| 91popny丨九色丨国产| 一级全黄少妇性色生活片| 久艹视频在线| 色站综合| 子洲县| 日日狠狠久久偷偷色综合96蜜桃| 平潭县| 日韩欧美中文字幕公布| 又长又大又粗又硬3p免费视频| 欧美40老熟妇色xxxxx| 国产老师开裆丝袜喷水视频| 亚洲av无码专区青青草原| 国内精品久久久久久99蜜桃| 国产欧美日韩中文久久| 被别人巨茎征服的娇妻3D动漫|